With this PTF, you can now specify the DLUS name at the node, port, and linkstation level. If a DLUS name is not specified, then the node level DLUS name is used by the ports and linkstations. However if a DLUS name is specified at the node and port levels, then the port level DLUS name is used for traffic in and out of that particular port. Similarly, if a DLUS name is specified at the linkstation level, then the linkstation DLUS name is used to for traffic in and out of that particular linkstation.
| Note: | In order to specify DLUS names at the port level, DLUS/DLUR must be enabled at the node level. |
Example 1 shows configuring a DLUS name at the port level. In this case, you specify both a primary and a backup DLUS.
Example 1:
APPN config> add port
APPN Port
Link Type: (P)PP, (FR)AME RELAY, (E)THERNET, (T)OKEN RING,
(S)DLC, (X)25, (FD)DI, (D)LSw, (A)TM, (I)P [ ]? T
Interface number(Default 0): [0]?
Port name (Max 8 characters) [T00000]?
WARNING!! You are changing an existing record.
Enable APPN on this port (Y)es (N)o [Y]?
Port Definition
Support multiple PU (Y)es (N)o [Y]?
All active port names will be of the form
Service any node: (Y)es (N)o [Y]?
Treat non-configured callers as LEN nodes: (Y)es (N)o [N]?
High performance routing: (Y)es (N)o [Y]?
Maximum BTU size (768-17745) [2048]?
Maximum number of link stations (1-65535) [65535]?
Percent of link stations reserved for incoming calls (0-100) [0]?
Percent of link stations reserved for outgoing calls (0-100) [0]?
Local SAP address (04-EC) [4]?
Local HPR SAP address (04-EC) [C8]?
Edit TG Characteristics: (Y)es (N)o [N]?
Edit LLC Characteristics: (Y)es (N)o [N]?
Edit HPR defaults: (Y)es (N)o [N]?
Edit Dependent LU Server: (Y)es (N)o [N]? Y
Fully-qualified CP name of primary DLUS []? STFNET.MVS1
Fully-qualified CP name of backup DLUS []? STFNET.MVS2
Write this record? [Y]?
The record has been written.
Example 2 shows changing the specified DLUS name at the port level to the default value.
Example 2:
APPN config> add port
APPN Port
Link Type: (P)PP, (FR)AME RELAY, (E)THERNET, (T)OKEN RING,
(S)DLC, (X)25, (FD)DI, (D)LSw, (A)TM, (I)P [ ]? T
Interface number(Default 0): [0]?
Port name (Max 8 characters) [T00000]?
WARNING!! You are changing an existing record.
Enable APPN on this port (Y)es (N)o [Y]?
Port Definition
Support multiple PU (Y)es (N)o [Y]?
All active port names will be of the form <port name sap>
Service any node: (Y)es (N)o [Y]?
Treat non-configured callers as LEN nodes: (Y)es (N)o [N]?
High performance routing: (Y)es (N)o [Y]?
Maximum BTU size (768-17745) [2048]?
Maximum number of link stations (1-65535) [65535]?
Percent of link stations reserved for incoming calls (0-100) [0]?
Percent of link stations reserved for outgoing calls (0-100) [0]?
Local SAP address (04-EC) [4]?
Local HPR SAP address (04-EC) [C8]?
Edit TG Characteristics: (Y)es (N)o [N]?
Edit LLC Characteristics: (Y)es (N)o [N]?
Edit HPR defaults: (Y)es (N)o [N]?
Edit Dependent LU Server: (Y)es (N)o [N]? Y
Fully-qualified CP name of primary DLUS [STFNET.MVS1]? <DEFLT>
Write this record? [Y]?
The record has been written.
Example 3 shows using the DLUS values specified at the node level. An explicit DLUS name is not configured at the port level.
Example 3:
APPN config> add port
APPN Port
Link Type: (P)PP, (FR)AME RELAY, (E)THERNET, (T)OKEN RING,
(S)DLC, (X)25, (FD)DI, (D)LSw, (A)TM, (I)P [ ]? T
Interface number(Default 0): [0]?
Port name (Max 8 characters) [T00000]?
WARNING!! You are changing an existing record.
Enable APPN on this port (Y)es (N)o [Y]?
Port Definition
Support multiple PU (Y)es (N)o [Y]?
All active port names will be of the form <port name sap>
Service any node: (Y)es (N)o [Y]?
Treat non-configured callers as LEN nodes: (Y)es (N)o [N]?
High performance routing: (Y)es (N)o [Y]?
Maximum BTU size (768-17745) [2048]?
Maximum number of link stations (1-65535) [65535]?
Percent of link stations reserved for incoming calls (0-100) [0]?
Percent of link stations reserved for outgoing calls (0-100) [0]?
Local SAP address (04-EC) [4]?
Local HPR SAP address (04-EC) [C8]?
Edit TG Characteristics: (Y)es (N)o [N]?
Edit LLC Characteristics: (Y)es (N)o [N]?
Edit HPR defaults: (Y)es (N)o [N]?
Edit Dependent LU Server: (Y)es (N)o [N]? Y
Fully-qualified CP name of primary DLUS [<DEFLT>]?
Write this record? [Y]?
The record has been written.
Example 4 shows configuring a primary DLUS name at the port level, but not specifying a backup DLUS name. If you do not specify a backup DLUS, this overrides the previously specified node and there will be no backup DLUS
Example 4:
APPN config> add port
APPN Port
Link Type: (P)PP, (FR)AME RELAY, (E)THERNET, (T)OKEN RING,
(S)DLC, (X)25, (FD)DI, (D)LSw, (A)TM, (I)P [ ]?
Illegal link type
APPN config>add port
APPN Port
Link Type: (P)PP, (FR)AME RELAY, (E)THERNET, (T)OKEN RING,
(S)DLC, (X)25, (FD)DI, (D)LSw, (A)TM, (I)P [ ]? T
Interface number(Default 0): [0]?
Port name (Max 8 characters) [T00000]?
WARNING!! You are changing an existing record.
Enable APPN on this port (Y)es (N)o [Y]?
Port Definition
Support multiple PU (Y)es (N)o [Y]?
All active port names will be of the form
Service any node: (Y)es (N)o [Y]?
Treat non-configured callers as LEN nodes: (Y)es (N)o [N]?
High performance routing: (Y)es (N)o [Y]?
Maximum BTU size (768-17745) [2048]?
Maximum number of link stations (1-65535) [65535]?
Percent of link stations reserved for incoming calls (0-100) [0]?
Percent of link stations reserved for outgoing calls (0-100) [0]?
Local SAP address (04-EC) [4]?
Local HPR SAP address (04-EC) [C8]?
Edit TG Characteristics: (Y)es (N)o [N]?
Edit LLC Characteristics: (Y)es (N)o [N]?
Edit HPR defaults: (Y)es (N)o [N]?
Edit Dependent LU Server: (Y)es (N)o [N]? Y
Fully-qualified CP name of primary DLUS [<DEFLT>]? STFNET.MVS3
Fully-qualified CP name of backup DLUS []?
Write this record? [Y]?
The record has been written.