1998 IEEE. Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from the IEEE.

IEEE Transactions on Antennas and Propagation
Volume 46 Number 2, February 1998

Table of Contents for this issue

Complete paper in PDF format

Micromachined Patch Antennas

Ioannis Papapolymerou, Student Member, IEEE, Rhonda Franklin Drayton, Member, IEEE, and Linda P. B. Katehi, Fellow, IEEE

Page 275.

Abstract:

This paper presents the use of selective lateral etching based on micromachining techniques to enhance the performance of rectangular microstrip patch antennas printed on high-index wafers such as silicon, GaAs, and InP. Micromachined patch antennas on Si substrates have shown superior performance over conventional designs where the bandwidth and the efficiency have increased by as much as 64% and 28%, respectively. In this work, the silicon material is removed laterally underneath the patch antenna to produce a cavity that consists of a mixture of air and substrate with equal or unequal thicknesses. Characterization of the micromachined patch antenna is presented herein and includes a discussion on the bandwidth improvements, radiation patterns, and efficiency of the patch. In addition, antenna placement on the reduced index cavity with respect to the high-index substrate is described to achieve efficiency improvements over conventional patch antennas.

References

  1. D. M. Pozar, "Microstrip antennas," Proc. IEEE, vol. 80, pp. 79-91, Jan. 1992.
  2. N. G. Alexopoulos and D. R. Jackson, "Fundamental superstrate (cover) effects on printed circuit antennas," IEEE Trans. Antenna Propagat., vol. AP-32, pp. 807-816, Aug. 1984.
  3. D. R. Jackson, J. T. Williams, A. K. Bhattacharyya, R. L. Smith, S. J. Buchheit, and S. A. Long, "Microstrip patch designs that do not excite surface waves," IEEE Trans. Antennas Propagat., vol. 41, pp. 1026-1037, Aug. 1993.
  4. M. J. Vaugh, K. Hur, and R. C. Compton, "Improvement of microstrip patch antenna radiation patterns," IEEE Trans. Antennas Propagat., vol. 42, pp. 882-885, June 1994.
  5. G. P. Gauthier, A. Courtay, and G. M. Rebeiz, "Microstrip antennas on synthesized low dielectric-constant substrates," IEEE Trans. Antennas Propagat., vol. 45, pp. 1310-1314, Aug. 1997.
  6. T. M. Weller, L. P. B. Katehi, and G. M. Rebeiz, "High performance microshield line components," IEEE Trans. Microwave Theory Tech. vol. 43, pp. 534-543, Mar. 1995.
  7. R. F. Drayton and L. P. B. Katehi, "Development of self-package high frequency circuits using micromachining techniques," IEEE Trans. Microwave Theory Tech., vol. 43, pp. 2073-2080, Sept. 1995.
  8. S. V. Robertson, L. P. B. Katehi, and G. M. Rebeiz, "Micromachined W-band filters," IEEE Trans. Microwave Theory Tech., vol. 44, pp. 598-606, Apr. 1996.
  9. E. O. Hammerstad and F. Bekkadal, "A microstrip handbook," Univ. Trondheim, Norway, ELAB Rep., STF 44 A74169, N7034, 1975.
  10. D. M. Pozar, PCAAD: Personal Computer Aided Antenna Design, Version 2.1, Dec. 1991.
  11. J. Ashkenazy, E. Levine, and D. Treves, "Radiometric measurement of antenna efficiency," Electron. Lett., vol. 21, no. 3, Jan. 1985.
  12. D. M. Pozar and B. Kaufman, "Comparison of three methods for the measurement of printed antenna efficiency," IEEE Trans. Antennas Propagat., vol. 36, no. 1, pp. 136-139, Jan. 1988.
  13. D. M. Pozar, Microwave Engineering.Reading, MA: Addison-Wesley, 1993.
  14. HP EEsof, Inc., Westlake Village, CA.