2000 IEEE. Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from the IEEE.

IEEE Transactions on Microwave Theory and Techniques
Volume 48 Number 4, April 2000

Table of Contents for this issue

Complete paper in PDF format

Miniaturized Artificial-Transmission-Line Monolithic Millimeter-Wave Frequency Doubler

Pekka Kangaslahti, Member, IEEE Petteri Alinikula, Member, IEEE and Veikko Porra Senior Member, IEEE

Page 510.

Abstract:

Millimeter-wave signals are typically generated by frequency multiplication in modern single-chip or multichip module (MCM) systems. Consequently,the multiplication efficiency, spurious rejection, and size of the frequency multiplier ultimately limit the integration level and cost of these systems. This paper points to the size reduction of millimeter-wave frequency doublers by evaluating artificial transmission lines (ATL's) as a means to minimize the size of the low-impedance shunt stubs. As a result, we developed a 40-GHz frequency doubler, which used only 0.6-mm2 area on a monolithic microwave integrated circuit. Despite the area minimization,the doubler exhibited state-of-the-art conversion loss of 1 dB over 10% bandwidth and rejected the fundamental frequency signal by more than 20 dB over 25% bandwidth. Reported herein is the novel simulation of the frequency doubler with active harmonic loads. Included in this paper are theoretical evaluation and simulation of ATL's with models for lumped components and verification of the results by electromagnetic simulation. Due to the high efficiency,low area requirement, and over 20-dB rejection of the fundamental signal,this miniaturized ATL frequency doubler can be used as a building block in the generation of local-oscillator signals in single-chip and MCM millimeter-wave systems.

References

  1. C. Rauscher, "High-frequency doubler operation of GaAs field-effect transistors", IEEE Trans. Microwave Theory Tech., vol. MTT-31, pp.  462-473, June  1983.
  2. C. Guo, E. Ngoya, R. Quere, M. Camiade and J. Obregon, "Optimal CAD of MESFET frequency multipliers with and without feedback", in IEEE MTT-S Int. Microwave Symp. Dig., New York, NY, May 1988, pp.  1115-1118. 
  3. A. Gopinath and J. B. Rankin, "Single-gate MESFET frequency doublers", IEEE Trans. Microwave Theory Tech., vol. MTT-30, pp.  869-875, June  1982.
  4. S. Maas, Nonlinear Microwave Circuits, Norwood, MA: Artech House, 1988, pp.  397-416. 
  5. I. Schmale and G. Kompa, "A Stability-ensuring procedure for designing high conversion-gain frequency doublers", in IEEE MTT-S Int. Microwave Symp. Dig. , Baltimore, MD, June 1998, pp.  873-876. 
  6. H. J. White, P. R. Gillette and V. J. Lebacqz, "The pulse-forming network,"in Pulse Generators, G. N. Glasoe, and J. V. Lebacqz, Eds. New York: McGraw-Hill, 1948, pp.  175-225. 
  7. P. Kangaslahti, P. Alinikula and V. Porra, "Millimetre wave signal generation using monolithic HEMT technologies", Analog Integrated Circuits and Signal Processing, vol. 15, pp.  123-133, Jan.  1998.
  8. I. Schmale and G. Kompa, "Choosing the right frequency doubler technology", in Proc. 2nd ESA Workshop Millimeter Wave Technol. Applicat.: Antennas, Circuits, Syst., Espoo, Finland,May 1998, pp.  467-472.