2000 IEEE. Personal use of this material is permitted. However, permission to reprint/republish this material for advertising or promotional purposes or for creating new collective works for resale or redistribution to servers or lists, or to reuse any copyrighted component of this work in other works must be obtained from the IEEE.

IEEE Transactions on Microwave Theory and Techniques
Volume 48 Number 8, August 2000

A High-Temperature Superconducting Duplexer for Cellular Base-Station Applications

Page 1336.

Abstract:

This paper presents a recent investigation of a high-temperature superconducting (HTS) duplexer for cellular base-station applications. The duplexer consists of two HTS hybrids and two HTS bandstop filters. The principle and design of the duplexer are described. The components of the duplexer were fabricated individually using double-sided YBa₂Cu₃O₇ (YBCO) thin films on LaAlO₃ (LAO) substrates. The substrate size for each of the hybrids was 0.5 × 22.5 × 15.5 mm, while each of the bandstop filters had a substrate size of 0.5 × 13× 38 mm. Experiments were performed both with a test housing in a liquid-nitrogen cooler at a temperature of 80 K and in an encapsulated RF connector ring in a vacuum cooler at 55 K. The measured insertion loss was less than 0.3 dB both from the antenna to receiver ports over a receive band of 1770-1785 MHz and from the transmitter to antenna ports over a transmit band of 1805-1880 MHz. The isolation between the transmitter and receiver was measured to be greater than 35 dB. Good measured results were also obtained for the encapsulated duplexer with the maximum insertion loss of 1.15 dB, the additional loss being due to the microstrip feed lines across the vacuum space, and the minimum isolation of about 30 dB.

References

1. D. Reeder, "A cryogenic option for expanding coverage", in Mobile Commun. Int. Conf., June 1996, p.  57. 
2. STI Inc. "A receiver front end for wireless base stations", Microwave J., vol. 39, no.  4, p.  116, 1996.
3. R. B. Hammond, "HTS wireless filters", Microwave J., vol. 41, no. 10, pp.  94-107, 1998.
4. M. J. Lancaster, Passive Microwave Device Applications of Superconductors, Cambridge: U.K.: Cambridge Univ. Press, 1997.
5. S. H. Talisa, M. A. Robertson, B. J. Meler and J. E. Sluz, "Dynamic range considerations for high-temperature superconducting filter applications to receive front ends", in IEEE MTT-S Microwave Int. Symp. Dig., 1997, pp.  997-1000. 
6. G. Koepf, "Superconductors improve coverage in wireless networks", Microwave RF, vol. 37, no. 4, pp.  63-72, Apr.   1998.
7. Y. Vourc'h, G. Auger, H. J. Chaplopka and D. Jedamzik, "Architecture of future basestations using high temperature superconductors", in ACTS Mobile Summit, Aalbourg, Denmark,Sept. 1997, pp.  802-807. 
8. R. B. Greed, D. C. Voyce, J.-S. Hong, M. J. Lancaster, M. Reppel, H. J. Chaloupka, J. C. Mage, R. Mistry, H. U. Häfner, G. Auger and W. Rebernak, "An HTS transceiver for third generation mobile communications-European UMTS", in IEEE MTT-S European Wireless Symp. Dig., 1998, pp.  98-103. 
9. M. Muraguchi, T. Yukitake and Y. Naito, "Optimum design of 3-dB branch-line couplers using microstrip lines", IEEE Trans. Microwave Theory Tech., vol. MTT-31, pp.  674-678, Aug.  1983.
10. T. Hirota, A. Minakawa and M. Muraguchi, "Reduced-size branch-line and rat-race hybrids for uniplanar MMIC's", IEEE Trans. Microwave Theory Tech., vol. 38, pp.  270-275, Mar.  1990.
11. I. Sakagami, T. Munehiro, H. Tanaka and T. Itoh, "Branch-line hybrid-rings with coupled-lines", in Proc. European Microwave Conf., 1994, pp.  686-691. 
12. J. P. Shelton, J. Wolfe and R. C. Van Wagoner, "Tandem couplers and phase shifters for multi-octave bandwidth", Microwaves, pp.  14-19, Apr.  1965.
13. "EM User's Manual", Sonnet Software Inc., Liverpool, NY, Ver. 2.4, 1993.
14. G. L. Matthaei, L. Young and E. M. T. Jones, Microwave Filters, Impedance-Matching Networks, and Coupling Structures, Norwood, MA: Artech House, 1980, ch. 12.